-
注塑、模具专业英语
Surface
Appearance
外观
Glossiness/gloss finish
光洁度、粗糙度
Matt
finish/matt surface
毛面
Glass fiber rich surface/glass
emergence on the
surface
玻纤外露、浮纤
Blooming/surface blooming
表面析出
White
patches on surface
表面白斑
Silver marks/silver streak
银纹
Splay mark
水纹、料花
Flow mark
流纹
Brittle/brittleness
脆、脆性
Bubbles/trapped gas
气泡
/
困气
V
oid
孔、气泡
Burn marks
烧伤
FR failed
阻燃不合格
Flame
rating V-2
阻燃等级
V-2
Poor dispersion
分散不好
FR/PTFE
…
agglomerates etc
阻燃剂
/PTFE
…结块
Pellet porous
颗粒料孔隙、
Low
impact/tensile strength etc
低冲击强度
/
拉伸强度等
High
flow/filler content etc
高流动性
/
过度填充
Longs/fines/doubles
长粒
/
碎屑
/
连粒
Poor cut
粒形不好
Bristle/voids
表面有小气泡
< br>/
孔
Glass
bundles
纤维结团
Product was rejected due to
产品不能接受因为…
High
moisture level
高
水分、高湿度
Warpage/warped
翘曲
/
变形
Shrinkage/shrink
收缩
/
收缩率
Sink marks
凹陷、缩水
Short shot/short molding
打
不满、欠注
Distortion
变形
Over dimension
尺寸过大
Under
dimension
尺寸过小
Flashing
飞边、披锋、溢边
Discoloration
变色
Off color
颜色差异
Flow rate
流动速率
Viscous/viscosity
粘性的、粘的
/
黏度
High
flow
高流动
Low flow
低
流动
Sticky
粘的,粘性的
Sticking core
粘后模,粘模芯
Sticking
sprue
粘水口
Sticking cavity
粘前模
Mold release<
/p>
(
agent
)
脱模
(
剂
)
Antioxidant
抗氧剂
Flame retardant agent
阻燃剂
Heat
stabilizer
热稳定剂
Chopped glass
fiber
短切玻纤
Roving
glass fiber
粗纱
/
长玻纤
Glass beads
玻璃微珠
Milled fiber
碾磨纤
Molybdenum disulfide/moly/MoS2
二硫化钼
Colorant
着色剂
Pigment
颜料
Dye
染料
Accepted
product specification
接受产品规格
Approved our product
认可我们的产品
Re-set
spec
重新定标准
Add in
extra
…
添加多一点…
Reduced
…
content
减少…含量
Dropped/reduced
…
by x
%
减少…含量…%
Confirmed
color standard
确认颜色标准
Approved color standard
认
可颜色标准
Re-confirmed color standard
重新确认颜色标准
Qualified our product
认可我们的产品
Undergoing heat aging test
在做热老化实验
Product
is under testing
产品在测试当中
Received first order
接
了第一个定单
Expected to finish by
…
预计在…完成
Expected
order is xMT
预计定单量…吨
Estimated annual/monthly consumption
p>
预
计年
/
月用量<
/p>
模具方面:
Ejection system
顶出系统、脱模系统
pin
顶针、推杆
spring
弹簧
Gate type
浇口类型
Sprue
主流道
runner
分流道
cavity
模腔
Sprue gate
直浇口
Pin point
gate
点浇口
Tab gate
护耳浇口
Fan gate
扇
形浇口
Tunnel or submarine gate
潜伏式浇口
Jump gate
跳跃式浇口
Diaphragm
gate
片状浇口