-
重新设置
Brocade SAM
Switch
交换机的密码
如果管理员忘记的博科交换机的密码可以通过一下方法对交换机的密码进行重设,
下面的方法在
brocade silkworm
200E
测试成功过。
可以试一下用
root
口令恢复:
root/fibranne
如果能登录,使用
passwddefault
命令重置密码。
通过如下方法取得<
/p>
root
权限
:
1.
连接串口并确定可以显示终端
2.
重启交换机,在终端上显示
“press ESC key
within 4 sec….”
时,
4
秒钟内按下
ESC
键
3.
会显示一个菜单,选择
Command Prompt
shell
4.
输入命令:
mount -o
remount,rw,noatime /
5.
输入命令:
mount /dev/hda2 /mnt
6.
输入命令
: passwddefault
或
passwd admin(
p>
仅重置
admin
用户密码
)
7. reboot -f
如果第
5
步
失败,则解决方法:
Printenv
找到
“OSRootPartition”
参数
,
然后
mount
第二个
partition
(
通常是
hda2)
p>
可以试一下用
root
口令恢复:
root/fibranne
如果能登录,使用
passwddefault
命令重置密码。
通过如下方法取得<
/p>
root
权限
:
1.
连接串口并确定可以显示终端
2.
重启交换机,在终端上显示
“press ESC key
within 4 sec….”
时,
4
秒钟内按下
ESC
键
3.
会显示一个菜单,选择
Command Prompt
shell
4.
输入命令:
mount -o
remount,rw,noatime /
5.
输入命令:
mount /dev/hda2 /mnt
6.
输入命令
:
passwddefault
或
passwd admin(
仅重置
a
dmin
用户密码
)
7.
reboot -f
***
如果第
5
步失败,则解决方法:
Printenv
找到
“OSRootPartition”
参数
,
然后
mount
第二个
partition
(
通常是
hda2)
200E
上有人这么做过
Your service request has been assigned
case number RQST.
If the Silkworm 12000
is using FOS v4.1.x or above then please follows
the instructions below to recover the
passwords.
Please let me
know if the 12000 is running FOS v4.0.x release.
Recovering the Root
Password on Fabric OS v4.1
If the Boot
PROM password is still known, you can use the
following procedure to recover the Root
password on a SilkWorm 3900 or SilkWorm
12000.
Note: This procedure requires
accessing the boot prompt, which stops traffic
flow through a SilkWorm
3900 until the
switch is rebooted. On a SilkWorm 12000, you can
recover the Root password without
disruption to I/O by performing the
procedure on the standby CP card.
To
recover the Root password:
1. Connect
to the serial port interface of the switch
(SW3900)/Standby CP(SW12000)
2. Reboot
the switch (SW3900)/Standby CP (SW12000) and press
ESC within four seconds after the
message
3. Enter the Boot
PROM password.
4. Enter
5.
Enter the printenv command and save the output.
6. Enter the boot command followed by
the first memory address after the string
OSLoader= obtained
from the printenv
output and -s
-
-
-
-
-
-
-
-
-
上一篇:PTN常见问题及处理方法
下一篇:记叙文阅读之联系上下文解释词语意思讲解与练习