-
Forward speech
Note: when you receive the 250A diesel
power generation electric welding machine, do not
know
how to operate, can Ou Bao this
generic generating and welding dual-purpose
machine manual
reference,
Zhang
Jialiang
is
think
so,
internal
combustion
electric
welder
and
gasoline
power
generation machine is
actually using the general!
1, add oil
(diesel power generation electric welding machine
to join 1.5 liters, 1 liters of gasoline
power generation electric welding
machine to add oil)
Remember do not add
too much or too little, more influence on the
service life, and no way to
start.
2, add fuel, check whether the battery
terminal has received immediately.
Start 3; (diesel welder throttle switch
should in gas state (right), and press and hold
the power of
the valve twist the key in
the ignition for two seconds and releasing
pressure reducing valve and
the key to
start the car), downtime is closed key press red
button at the throttle switch below,
throttle release natural stop and start
all over again must be added the throttle switch.
Gasoline
welding machine is started.
First of all, the door should be in the open state
(air filter above the
throttle pull rod
pull out), then direct twisting key ignition
start, start after the first time to close
the throttle (choke rod must press
enter)
5, when the welder should
maintain maximum current switch open, DC
regulating switch must be
twisted to
the maximum. The machine is best not to use other
appliances when using welding
work, if
necessary to use appliances, you can use her own
watch.
6, welder quick joint then
qualify the provisions of is to use more than 35
square or 50 square
feet of Doppler
line, too much is not good, too small will burn),
the length of the provisions is less
than 8 meters, principle of not more
than 10 meters, remember if connected to the
output line is
too
long
will
affect
the
service
quality,
will
lead
to
black
smoke,
the
card
machine,
even
the
shutdown
of phenomenon
7, welder red fast joint
interface is welding (welding). Black is a is
connected with the guide wire,
remember, pick the wrong can not be
normal use.
An all
The following marks, to
remind the user, once operational errors, may
cause personal injury.
Once the
operation mistake, may cause death or serious
injury. Once the operation error, may cause
moderate damage or loss of material.
Although it will not cause the
accident, but will affect the performance of the
machine life.
1 safe use
Note the use of fuel before the 1-1
operation notice
This fuel for diesel
fuel, there shall be no machine around the
kindling, in case of fire.
You must
stop the gas, and the diesel must be dried with a
cloth. The exhaust pipe shall not be placed
around the fuel or other flammable.
Exhaust note
This causes
livestock poisoning in long time will use bad
ventilation indoors or in enclosed spaces.
Notes on the use of
This
daily inspection, regular inspection, maintenance,
refueling, cleaning work, must first stop, then
press the
Electric shock,
leakage precautions
Audiences to
prevent electric shock, leakage, please don't with
wet hands or in the rain and snow and
machine is wet operation and use.
In the operation, please do not touch
the welding terminal by hand, must first stop,
then the welding
wire.
I do
not use the damaged insulation rubber welding
wire.
Note when cleaning the machine
Onion
please
fabric
or
compressed
air
cleaning,
is
not
available
for
washing
or
cleaning
agents,
in
order to avoid insulation
deterioration, malfunction.
Security
issues outside of the
When handling the
matters needing attention 1-2
I
installed or unloading machine, please use the
rope, the pulley frame hanging on horizontal
loading,
not available rope engine
parts or generator parts.
This machine
must be shut down when handling machine.
Sandy, when in use, please under the
machine pad plate, to prevent sand suction within
the engine
caused by bad insulation.
I refer to 1-1
Note before the start of the 1-4
This worker should wear overalls,
gloves, hats, welders, using a mask.
Should be checked before starting, if
there is abnormal, first maintenance and then
start.
Reference 1-1
Note in
1-5 operation
Run in or just off, the
exhaust pipe temperature is very high, careful
burns.
Reference 1-1
1-6
maintenance, custody matters needing attention
Please place in a dry, clean, low salt
room.
To avoid long-term use of plastic
cloth cover, so as to avoid rust or poor
insulation.
Before long-term storage,
please remove the battery, put a clean fuel, make
maintenance, in order to
use.
At least 3 months to run once, to
confirm the status of the machine.
Reference 1-1
2
specification and data
TO250A-
柴油发电电焊机
产品编号
TO250A
款式
手推式
品牌
大泽动力
额定输出功率
HP
20
绝缘等级
F
电焊机下降特性
单把电流调节范围
0-250A
空载电压
65V
工作电压
22-30V
负载持续率
100%
适用焊条
φmm
2.0
~
5.0
电焊同时辅助功率
额定输出
KW
5
最大输出
KW
6
发电机
额定电压
V
220
(可选配
380V
)
耗油量
205g/kw.h
功率因数
%
工作状态
发动机
名称
发动机形式
缸体数
排气量
额定转速
rpm
启动方式
燃油型号
100
连
续
192F
(
YOTOTI
)
单缸
直列
四冲程
风冷柴油机
1
420CC
3000
手启动
|
电启动
0
号柴油
(夏)
-10
号柴油
(冬)
其他
工作环境温度
℃
油箱容量
L
最大尺寸
mm
净重
Kg
噪
音
dB
机油容积
连续工作
12H
-20
~
40
20
770*510*660
120
70
1.05L
Payment:
100% advance payment, payment to the delivery.
Delivery
date:
within
2
working
days
after
receipt
of
your
order
and
remittance.
Europe Bao power source in Italy
Contact: Zhang Gong (Manager)
Tel:
Fax
-
-
-
-
-
-
-
-
-
上一篇:胜利之歌第三季第一集部分台词
下一篇:千法之书——防护学派