零部件条形码规范

推荐的可读说明字符是

OCR-A

2.4MM

The readable description of barcode must represent the character of the coding, putting above or

below the barcode. The recommended readable description character , the height of which is not

lower than 2.4MM or the character is OCR-A.

2.4

空白区：

Blank Area:

条形码左右两头空白区最少应为

6. 5MM

，上下空白区最少

1MM

，对于 大件部件如前、

后悬架总成，上下空白区最少

2MM

The blank area on the right and left side of barcode should at least 6.5MM, the above and the

bottom not lower that 1MM. As to those bigger component, for example front or rear suspension,

the above and the bottom side of blank area should be at least 2MM.

3.

标签材料：

label material

3.1

标签材料

条形码可以印制在不同的标签材料 如纸，聚酯或金属上，对标签材料和相关联的胶水的

选择基于应用和工程性能的要求。零 部件供应商应根据

SGM

要求选择标签材料，使得标签固

定到最后零件外形上以供扫描时，能满足规范的条件及工程要求。对供应商提供的零部件在

SGM

总装后标签暴露在外的，应使用聚酯标签材料。要求在零件正 常使用中不脱落

.

Barcode can be printed on different label materials such as paper, polyester or metal surface while

the choice of the label material and relative glue is based on the applicable and engineering

demand. According to the different demand of SGM, the suppliers need to choose variable label

material in order to meet the needs of the standard condition and engineering demand when all the

components fixed on the finished components figure are being scanned. If those components barcode

provided by the supplier are always explosive outside after installed in SGM, The polyester label

material must be used.

require not to shed when parts are in normal using.

3.2

墨水：

ink:

在制作条形码标签时可使用两种墨 水，制作条码数据时要求用可读墨水，条形码数据背

景必须用不可读墨水。不可读墨水是 任一种对条形码扫描设备来说与条形之间的空格一样作用

的墨水。可读墨水通常为黑色颜 料为基础的墨水，用来打印条形码标签，必须使用不渗透的墨

水

.

When making barcode label, we may choose two kinds of ink; one is readable ink for making

barcode data and the other is nonreading ink for making background of barcode data. Nonreadable

ink

is

the

one

having

the

same

effect

as

the

blank

one

between

the

barcode

when scanned

by

any

barcode

scanning

equipment.

However,

readable

ink

choose

the

pigment

black

as

the

based

ink;

moreover it must use unseeping ink when printed for code label.

4

．打印标签要求

Requirement of printing label

4.1

打印设备

print equipment

使打印出来的条形码清晰，应使用激光 打印机或专用条码打印机，例

HP

4000P

激光打印

机

，

Zebra 140 XII

条码打印机。

To make the code printed clear, we should use laser printer or professional label printer. For

example HP 4000P laser printer, Zebra 140 XII label printer.

4.2

质量保证要求

quality assurance requirement

供应商应建 立质量保证程序，以保证标签质量和本规范的要求。应包括当

SGM

零件或图

号发生变更时，由断点引起的相应条形码变化，条形码标签批准和修改，条 形码标签打印质量

检验。

Suppliers should establish the program of quality assurance to ensure the quality of label

and requirement of this standard. It includes the approval and amendment of code when SGM

component or chart marks alter so as to induce the change of relative barcode because of breakpoint

and the quality test when they print barcode label.

4.3

打印质量检查要求

Requirement of printing quality check < /p>

比例符号级别以及给出的尺寸的测量。

对打印的条形码检查应该由 以下部分组成：

检查正

确的信息编码，对条形和空格宽度

.

供应商每个零件的初始条形码应经

SGM

采购部和

IT

部确认

< br>.

All the code test of printing should compose of the following portions: checking the correct of

Information coding, surveying the width of code and blank, the grade of proportion sign and the

provided size.

Each original barcode of supplier's parts should be authenticated by

purchasing team and IT team in SGM.

5

．条形码信息格式：

format of code information

5.1

零部件验证

(VCVS)

和可追溯性

VCVS and traceability

零部件验证

(VCVS)