-
电缆沟开挖施工方案
Work
Method
of
Cable
Trench
Excavation
编
制:
Compiled by:
审
核:
Reviewed by:
20
09
年
10
月
21
日
October 21,
2009
目
录
Content
一
.
概况
OVERVIEW .........................................
..............
3
1.1
工程概况
PROJECT OVERVIEW
..........................................
3
1.2
施工范围
SCOPE OF WORK
.............................................
3
二.编制依据
COMPILATION BASIS
...........................................
4
三.
施工工艺流程
CONSTRUCTION PROCESS:
...................................
4
四
.
前期准备
PREPARATIONS
................................................
4
4.1
技术准备
TECHNICAL PREPARATION
......................................
4
4.2
材料准备
MATERIAL PREPARATION
........................................
5
4.3
主要机具准备
MAIN EQUIPMENTS
PREPARATION
.............................
5
4.4
作业环境准备
OPERATING ENVIRONMENT
PREPARATIONS
......................
5
五
.
电缆沟施工
CABLE TRENCH
CONSTRUCTION
.................................
5
5.1
电缆沟测量、定位
CABLE TRENCH
MEASUREMENT AND POSITIONING ...........
5
5.2
电缆沟开挖
CABLE TRENCH EXCAVATION
..................................
6
六
.
质量控制
QUALITY CONTROL
< br>..............................................
7
6.1
电缆沟外形尺寸允许偏差表
ALLOWABLE
DEVIATED EXTERNAL DIMENSIONS OF CABLE
TRENCH TABLE
...............
..............................................
7
6.2
应注意的质量问题
QUALITY ISSUES
......................................
8
七
.
成品保护
FINISHED PROTECTION
..........................................
8
八
.
施工记录
CONSTRUCTION OF RECORD
.......................................
8
九
.
安全生产、文明施工要求和措施
SAFETY
AND
CIVILIZED
CONSTRUCTION
REQUESTS
AND
MEASURES
....
..................................................
...........
9
附厂区电缆沟图:
ATTACHED: CABLE
TRENCH DRAWING
.
..........................
9
一
.
概况
Overview
1.1
工程概况
Project Overview
项目名称:
本工程涉及三个变电站,分别是现有的
220/35kV
A472
变电站、现有的
35/10kV B301S
变电站
以及新建的
35/10kV C581<
/p>
变电站,工作内容为三个变电站之间和从三个变电站接至
MV
p>
用户的
电力电缆、控制电缆、接地电缆敷设所需电缆沟的开挖工程。
The project involves three
substations,
namely
the
existing
220/35kV
A472
substation,
the
existing
35/10kV
B301S
the 35/10kV C581
substation and a new substation. This is the
power, control and
grounding cable
trench excavation project among three substations
and for MV users
connected to the three
substations.
1.2
施工范围
Scope of Work
1)
由
A472
变电站引出
3
路
35kV
出线。其中:
一路引至
B301S
建筑
(
35/10kV<
/p>
变电站)
原
1#
主变,
原
1#
主变电缆将抽出,
与新增
4#
主变连接;
另两路引至
35/10kV C581
变电站
1#
主变和
2#
主变。回路采
用
FS-YJY-26/35kV-1*300mm2
单芯
p>
电缆,直埋敷设。去
C581
的两路
35kV
线路,敷设时沿不同路径,以避免两回线路同时受损。
Pull three 35V outgoings from A472
substation. Of which:
The first
outgoing is led to B301S Building (35/10kV
substation) the original one #
main
transformer, pull the original one # main
transformer cable out, and connect to
the adding 4 # main transformer; the
other two outgoings are led to 35/10kV C581 # 1
and substation 2 # main transformer.
Use FS-YJY-26/35kV-1 * 300mm2 single-core cables
for Loop and buried pulling. Two 35kV
lines to C581 are laid along different paths to
avoid damage of the two loops.
2)
由
B301S
变电站引出
7
路
10kV
p>
出线。全部引至
B399
中心制冷站。回路
采用
10kV
截面为
95mm2
的三芯铠装电缆,由
B301S
南面现有的电
缆井引出直埋至装置。
Pull 7 10kV outgoings from
B301S
substation
to
B399central
refrigeration
station.
Loop
uses
10kV
three-core
armored cable
with cross-section 95mm2 and pull out from the
existing cable well in
the south of
B301S then buried lay to the device.
3)
由
C581
< br>引出
10
路
10kV
线路,
分别为
A507
的
四台变压器,
B551
的两台变压器,
B553TDA
装置氢
气压缩机
2
p>
台,
C521
盐酸装置氯气压缩机
1
台,盐酸压缩机
1
台
提供电源。其中,变压器回路
采用
10kV
截面为
185mm2
的三芯铠装电缆,马达回路采用
10kV
截面为
95mm2
< br>的三芯铠装电缆。
以上电缆线路均沿规划路径埋地敷设。
10
10kV
lines
led
from
C581
are
used
to
supply
power
-
-
-
-
-
-
-
-
-
上一篇:通信线路工程验收规范
下一篇:企业社会责任的英文文献综述