-
错
误
和
警
告
解
析
Model
Size
(current
problem)1.183933e+000,BTOL
setting
1.00000e-005,minmum
KPT
distance 4.308365e-006
先在要分割的地方设置一个工作平面,
用布尔运算
“
divided
--volume by
working
plane
”
进行分割的时候,出现上述错误,主要
愿意可能是设置的公差太小,
当时试了几次都么有成功,最后
干脆把体重新建立了一个,又画了一个很大的面,终于成功
了。
2.
一个常见的代表性错误!
原来我的虚拟内存设置为“无分页文件”
,现在改为“系统管理”
,就不在出现计算内存不够
的情况
了。
Error!
Element type 1 is Solid95,which can not
be used with the AMES command, meshing of
area 2 aborted.
刚开始学习的人经常出这种错误,这是因为不同单元类型对应不同的划分网格操作。
<
/p>
上面的错误是说单元类型为
Solid95
(实体类型)
,不能用
AMES
命令
划分面网格。
3
Meshing
of
volume
5
has
been
aborted
because
of
a
lack
of
memory.
Closed
down
other
processes and/or choose a larger
element size, then try the VMESH command again.
Minimum additional memory
required=853MB
(
by kitty_zoe
)
说你的
内存空间不够,
可能因为你的计算单元太多,
增加
mesh
尺寸,
减少数量或者增加最小
内存设定(
ansys10
中在
customization preferences
菜单存储栏
可以修改)
你划分的网格太细了,内存不足。建议将模型划分为几个部分,分部分进行划分,可以减少
内存使用,试一下!
input volumes do not meet the conditions required
for the VGLU operation . No
new
entities were created . The VOVLAP operation is a
possible alternative
VGLU
p>
是将两个或多个体粘到一块,体之间的交集应该是面,帮助里的说法,
This
operation
is
only
valid
if
the
intersections
of
the
input
volumes
are
areas
along
the
boundaries
of those volumes<
/p>
。你粘结
glue
的体可能有重叠,所以
后面提示了一个
VOVLAP
命令,该命
令是将两个或多个体的重叠部分拿出来作为结果
VMESH
划分时,精度不同,单元数量差别太大了,如果是自由网格划
分,那么尝试几个
SMRT
等级看看。还有就是单元形状不同,
产生的网格质量也差别很大,我前几天才重新划了一次
网格,印象很深。
shape,0,3d
和
shape,1,3d
就是划分体时控制单元形状的
is not a recognized GEGIN
command,abbreviation,or macro.
this
command will be ingored.
那是因为打开了前处理,求解或者后处理,
< br>先用
FINISH
命令,再用
C
LEAR
就可以了
6.
约束不总,产生刚性漂移
我觉得这个不一定就是约束不足造成的刚性漂移。另外一个可
能的原因是网格划分的不好。
在曲线变化剧烈的区域,如果网格划的太疏,也可能产生这
样的错误。
error
occured during sweeping while meshing arer
element sizing
parameters(RSIZE,LESIZE,etc).or
mesh
this
arer
manually(AMESH
or
AMAP).then
try
the
VSME command again .The
VSWE command is ignored.
在对
一个规则的体进行扫略划分的时候,出现了这个命令,原因是边的尺寸,或者单元的个
数
设置不合理,对应不上,就行变数核对皆可解决问题!
1 cannot be meshed. 208 location(s)
found where non-adjacent
boundary
triangles touch. Geometry configuration may not
be valid or
smaller element size
definition may be required.
提示就是告诉你需要更小的单元
可能
单元太大的时候出现的网格有有问题,比如狭长的网格,计算的时候集中应力太大
testing revealed that 3 of
the 13 new or modified elements
violate shape warning limits. To
review test results, please see the
output file or issue the CHECK command.
ansys
里面有自己带的网格检
查,这说明你的网格尺寸有问题,重新划分
10.
划分
solid45
单
元的时候出现了
structural elements without mid
nodes usually
produce much more
accurate results in quad or brick shape
提示你采用带中间节点的单元进行计算。但是
solid45
六面体网格精度一般够了,不需要理
会
。
11.
:
Volume11
could not be swept because a source and a target
area could not be
determined
automatically
。
please try
again...
体不符合
SWE
EP
的条件,把体修改成比较规则的形状,可以分割试试
12.*** WARNING ***
SUPPRESSED MESSAGE CP = 1312.641 TIME=
16:51:48
An error has occurred writing
to the file = 12 which may imply a full
disk.
-
-
-
-
-
-
-
-
-
上一篇:netapp客户端操作
下一篇:园林常见水生植物图片及简介