-
气动一液压动力单元
HP 015<
/p>
,
016
,
01
7
操
作
说
明
书
目录
1
、设计与功能
2
、安装
3
、调试
4
、维修
5
、技术数据
6
、系统组件
6.
1
气动边缘探测器
6.
2
回中心调解
FM 20 01
6.
3
液压缸
Pneumatic-
hydraulic power units are used as constituent
parts of web
guiding
systems
for
laterally
positioning
running
webs
or
displacing
let-off
or
re-wind
stations.
These
devices
have
been
conceived
for
guidance by a single edge
气动
液压动力单元是作为放卷和收卷的横向边缘定位系统的组成
部分,用以定位极片边沿。<
/p>
1
、
Design
function
1
、设计与功能
The
pneumatic-hydraulic
power unit is built around
a
sealed oil tank (11/Fig .
1).
On the top
plate of
the tank are found:
气动一液压动力单
元安装在密封油箱(
11/
图
1
)的顶板上:
-
3-phase
motor
(
1/fig.
1
)
-
三相异步电动机(
1/
图
1
)
< br>
and
-
Side channel
blower
-
鼓风机(
4
)
-
Air inlet
filter
-
空气进气过滤器(
5
)
-
Oil pressure
filter
-
压力油过滤器(<
/p>
20
)
-
Air manifold
-
空气歧管(
11
)
-
Servo-valve
-
伺服阀(
21
)
-
2/2 way valve
for when setting the dis-placement guider
assembly via
pushbuttons or
lock-out.
-
2/2
油阀(通过按钮设置位移导向组件或锁定)
(
< br>10/
图
4
)
< br>
-
2/2way
valve(9/Fi g.
1)for air
signal connections.
-
2/2
阀
,空气信号连接(
9
)
The hydraulic gear wheel pump (22 Fig .
1) together with the oil
intake filter
(23/Fi g . 1) and the pressure regulating valve
(xx /Fi g . 1)
are found in the oil
tank(1/Fi g. 1)
液压齿轮泵
(
22
图
0. 1
)
进油过滤器
(
23
图<
/p>
1
)
和压力调节阀
(
XX/
FI
?
.
1
)一起安装油箱(
1/Fig0.
1
)
A
、
B
Hydraulic
cylinder connection
液压缸连接口
GL
Bias valve for synchronisation of
cylinder
positioning speed
偏置阀,同步气缸定位速度
OIL
Oil
inlet with air
filter
进油口与空气过滤器
R
Valve for reponse
sensitivity adjustment
调节响
应灵敏度阀门
S1
Connections
detector for high air
pressure(emitter)
连接探测器高气压(发射)
S3
Connection return-to-centre
operator
连接回中
装置
S2
、
S4
Connections detector for low air
pressure(receiver)
连接探测器的低气压(接收)
NO.
序号
1
2
3
4
5
6
Oil reservoir
油箱
Motor
电动机
Terminal box
接线盒
Blower
鼓风机
Air-filter
空气过滤器
Air-hose
connection port
空气软管连接端口
7
Air-hose connection port
空气软管连接端口
8
Air-hose connection port
空气软管连接端口
9
Solenoid valve
电磁阀
8030B10
S2. 2
(
for center
stop
)
S2.
1
(
for
sensor
)
Capacity
12. 5L
容量
12. 5L
0. 4kw 4
极
3
相
S1
(
for
sensor
)
Designation
名称
Type
型号
10
Air-hose
connection port
空气软管连接端口
C1 C2 1/4
”
A
、
B
11
12
13
阀
14
15
16
17
18
19
20
Air manifold
空气歧管
Adjusting
knob
调节旋钮
Flow
control valve
流量控制
GL
Oil inlet port
进油口
Oil level
gauge
油位计
Drain
port
卸油口
Water
gauge
液位标尺
图
2
Internal wiring diagram
内部线路图
To provide
the air for the detector, ambient air is drawn
through an
inlet
filter
(3/Fig .
2)into
the
side
channel
blower
(2/fig.
2)
and
fed
to
connection S1 of the pneumatic detector
FL 1.
The detector air pressure
can be adjusted by
valve R
located in the inlet port of the side
channel
blower to suit the appropriate
application (e. 9. thin materials).
为探测器提供的空气,环境空气通过进气过滤器(
23
侧通道鼓
风机(
2/fig
< br>。
2
)并反馈给连接
S1
的气动探测器
FL1
。探测器的空气
压力可以通过位于进气口的侧通道鼓风机阀
R
调
整,以适应不同的
应用场合(
E.9
。
薄膜材料)
。
Some
of
the
air
under
pressure is diverted
through
the
fixed
valve
-
-
-
-
-
-
-
-
-
上一篇:计算机主板的组成详解讲解
下一篇:Award Bios 设置超详细图解