-
Brocade
光纤交换机常用命令
标签:
Brocadesan
交换机命令
2013-12-24 10:19
2062
人阅读
评论
(0)
收藏
举报
分类:
San
IBM
的双机双柜,两光纤交
换机分别引一根光纤到另一楼光纤交换机,插上无
反应,后得知需要更改交换机的
domain id
默认出厂为
1
。需改为不同号。下
面是博科的交换机命令转。
.163./blog/static/116675/
Brocade
SAN
交换机常用命令
使用电脑连接
管理网口,默认
IP
地址为:
192.
168.0.1
,掩码:
255.255.255.0
默认用户名:
admin
,默认密码
password
1. switchStatusShow
查看交换机的总体健康状态
switch:admin> switchstatusshow
Switch Health Report
Switch
Name: SWFCR
IP address: 10.33.54.176
SwitchState: MARGINAL
Duration: 863:23
Power
supplies monitor MARGINAL
Temperatures
monitor HEALTHY
Fans monitor HEALTHY
WWN servers monitor HEALTHY
Standby CP monitor HEALTHY
Blades monitor HEALTHY
Flash
monitor HEALTHY
Marginal ports monitor
HEALTHY
Faulty ports monitor HEALTHY
Missing SFPs monitor HEALTHY
All ports are healthy
switch:admin>
2. switchShow
查看交换机基本配置信息
Enter
the switchShow command, which displays the
following information for a switch:
-
switchname - The switch name.
-
switchtype - The switch model and firmware version
numbers.
- switchstate - The switch
state: Online, Offline, Testing, or Faulty.
- switchrole - Displays the switch
role: Principal, Subordinate, or Disabled.
- switchdomain - Displays the switch
Domain ID.
- switchid - The embedded
port D_ID of the switch.
- switchwwn -
The switch World Wide Name.
-
switchbeacon - The switch beaconing state: either
ON or OFF.
The switchShow command also
displays the following information for ports on
the specified
switch:
-
Module type - The SFP type if an SFP is present.
- Port speed - The speed of the Port
(1G, 2G, 4G, N1, N2, N4, or AN). The speed can be
fixed, negotiated, or auto-negotiated.
- Port state - The port status.
- Comment - About the port. This
section may be blank or display the WWN for an
F_Port or
an E_Port, the trunking
state, or upstream or downstream status
3. portShow
查看端口状态
switch:admin> switch:user> portshow 0
portName:
portHealth:
OFFLINE
Authentication: None
portDisableReason: None
portCFlags: 0x1
portFlags:
0x4001 PRESENT U_PORT LED
portType: 4.1
portState: 2 Offline
portPhys: 2 No_Module
portScn: 0
port generation
number: 0
portId: 010000
portIfId: 43020020
portWwn:
20:00:00:60:69:00:02:53
portWwn of
device(s) connected:
Distance: normal
portSpeed: N2Gbps
LE domain:
0
Interrupts: 0 Link_failure: 0 Frjt: 0
Unknown: 0 Loss_of_sync: 0 Fbsy: 0
Lli: 0 Loss_of_sig: 0
Proc_rqrd: 0 Protocol_err: 0
Timed_out: 0 Invalid_word: 0
Rx_flushed: 0 Invalid_crc: 0
Tx_unavail: 0 Delim_err: 0
Free_buffer: 0 Address_err: 0
Port part of other ADs: Yes
4. fanShow
查看交换机散热风扇的状态
Enter the fanShow command:
switch:admin> fanshow
Fan 1
is OK speed is 7010 RPM
Fan 2 is OK
speed is 7180 RPM
Fan 3 is OK speed is
7068 RPM
Fan 4 is OK speed is 7116 RPM
Fan 5 is OK speed is 7155 RPM
Fan 6 is OK speed is 7001 RPM
switch:admin>
5. psShow
查看交换机的电源状态
注:如果安装
FR4-18i
、
FC4-16IP<
/p>
、
FC10-6
、
FC8-48
板,需要满配
4
个电源
Enter the psShow command:
switch:admin> psshow
Power
Supply #1 is OK
0335,FF2Z0007161,60-0000739-02,
B,,DCJ3002-01P, B,FF2Z0007161
Power
Supply #2 is faulty
0335,FF2Z0007176,60-0000739-02,
B,,DCJ3002-01P, B,FF2Z0007176
switch:admin>
6. tempShow
查看交换机的环境温度
Enter
the tempShow command:
switch:admin>
tempshow
Index Status Centigrade
Fahrenheit
----------------------------
------------------------
1 OK 21 70
2 OK 22 72
3 OK 29 84
4 OK 24 75
5 OK 25 77
switch:admin>
7. errDump
、
errShow
、
e
rrClear
查看交换机的部消息日志
To display the system message log, with
no page breaks
Enter the errDump
command.
To display the system message
log one at a time
Enter the errShow
command.
To clear the system message
log
Enter the errClear command.
8. supportShow
、
su
pportSave
、
pdShow
收集交换机的诊断数据
supportShow
显示诊断信息和状态信息
supportSave
将数据打包、上传至指定的
FTP
服务器
The
command prompts for an FTP server, packages the
following files, and sends them to the
specified server:
? The
output of the supportShow command
? The
contents of any trace dump files on the switch
? System message logs (for Brocade
directors, supportSave saves the system message
logs
from both of the CP blades)
pdShow
显示
panic du
mp
文件的容,帮助诊断系统
panic
的原因
9. nsShow
、
p>
nsAllShow
、
fabricSho
w
检查连接到交换机的设备
nsShow
显示连接到交换机的所有设备
nsAllShow
显示连接到
Fa
bric
的所有设备
fabricShow
显示
Fabr
ic
中的所有交换机
10.
licenseShow
、
wwn
检
查
license
文件和交换机的
WW
N
号
11. version
检查
Fabric
OS
的版本,将显示如下信息:
-
Kernel: displays the version of switch kernel
operating system.
- Fabric OS: displays
the version of switch Fabric OS.
- Made
on: displays the build date of firmware running in
switch.
- Flash: displays the install
date of firmware stored in nonvolatile memory.
- BootProm: displays the version of the
firmware stored in the boot PROM.
12.
haShow
查看
Control
Blade
的状态
swDir:
admin> haShow
Local CP (Slot 6, CP1):
Active
Remote CP (Slot 5, CP0): Standby
HA Enabled, Heartbeat Up, State
Synchronized
13. slotShow
查看
各个
Blade
的状态
14. portCfgSpeed
修改端口的速率
15. portE
nable
或
portCfgPersistentEnabl
e
Reset
端口
16.
检查
WWN
< br>卡状态
下列命令如果不能正确执行,则说明
WWN
卡需要更换:
,
chassisShow
:显示交换机的
WWN
号
chassisShow
:显示
chassis
和
WWN
卡的状态
ipAd
drShow
,
ipAddrSet
:
显示
CP Blades
的
IP
地址
historyShow
、
historyLastShow
:显示历史日志
信息
switchName
:显示交
换机的名字
修改
Domain ID
1.
查看当前的
Domain ID
输入命令
fabricShow
,输出
结果中的
Switch
ID
即包括交换机的
Domain
ID
。
2.
先关闭交换机
输入命令
swichDisable
3.
配置
Domain ID
输入命令
configure
Enter y after the Fabric Parameters
prompt:
Fabric parameters (yes, y, no,
n): [no] y
Enter a unique domain ID at
the Domain prompt. Use a domain ID value from 1
through 239 for
normal operating mode
(FCSW compatible):
Domain: (1..239) [1]
3
Respond to the remaining prompts, or
press Ctrl-d to accept the other settings and
exit.
4.
重新启用交换机
输入命令
swichEnable
升级
Firmware
FC10-6
Blade
需要
Firmware Version
5.3
以上
FC4-16IP
Blade
、
FC4-48 Port
Blade
需要
Firmware Version
5.2
以上
FR4-18i
router blade
需要
Firmware
Version 5.1
以上
如果<
/p>
M48
有主备
Control Proc
essor
,且主备
CP
处于
synchronized
状态,则
升级过程可
在线进行,不干扰数据流量。
如果
M
48
只有一个
CP
,则升级微码过程中
需要
reboot
交换机来激活新的
F
irmware
,数据访问会中断。
升级
M48 Firmware
约需<
/p>
15
分钟
1.
保存交换机的配置信息
configUpload
2.
保存主备
Control Processor
Blade
的
supportsave
使用命令
ipAddrShow
,查看主备
< br>CP
的
IP
地址
使用
telent
分别登录
主备
CP
,使用命令
supportS
ave
分别收集主备
CP
的
supportsave
文件。
3.
查看
supportsave<
/p>
中的
XXX_SUPPORTSHOW
文
件,查找如下字段:
/bin/df:
Filesystem 1k-blocks Used Available
Use% Mounted on
/dev/root 120112 61128
58984 51% /
/dev/hda2 120128 72356
47772 60% /mnt
确认
Flash
存储器的使用率不超过
90%
。否则需联系二线
p>
Support
。
4.
清除交换机中当前保存的
error
report
信息
errClear
5.
检查当前各个
CP Blade
s
的
Firmware
版本
firmwareShow
6.
检查主备
CP
状态,是否处于同步状态
haShow
:查看主备
CP
是否处于
Synchronized
状态
如果主备
CP
不处于同步状态,则使用命令
haSyncStart
同步主备
CP
。
switch:admin> hashow
Local
CP (Slot 5, CP0): Active, Warm Recovered
Remote CP (Slot 6, CP1): Standby,
Healthy
HA enabled, Heartbeat Up, HA
State synchronized
7.
升级
Firmware
如果
SAN
交换机支持
HA
,则使用命令
firmwareDownload
,同时升级主
备
Control Blade
。
<
/p>
如果
SAN
交换机不支持
HA
,则使用命令
firmwareDownload
-s
,分别升级每个
Control
Blade
。
8.
检查
Firmware
升级是否完成
< br>
firmwareDownloadStatus
9.
再次检查当前各个
CP Bla
des
的
Firmware
版本
firmwareShow
激活软件
License
-
-
-
-
-
-
-
-
-
上一篇:ABAQUS实体单元类型总结
下一篇:(单位)机构编制情况自查报告