-
Abaqus
中三维几何体生成结构网格的分割方法
图
1
可以直
接生成结构网格的三维几何体
图
2
不可以直接生成结构网
格的三维几何体
几何体中有孔
圆弧
≥900
有不能生成
二
维结构网格的面
一个项点有三条以上的边共用
图
3
分割
示例
无法生成结构网格的问题
分割示例
1
几何体中有孔
如将孔分割成半圆或者
1/4
圆从而去除孔
2
圆弧
≥900
< br>如将
1800
圆弧分成两个
90
0
圆弧
3
有不能生成二维结构网格的
面
如半圆周面只含有二个边而一个面至少含有三条以上的
边界才能生成二
维结构网格所以将半圆分半这样每个面便
有三条边
4
一个顶点只能有三条边共用
5
一个区域至少
有四个面如四面体
6
如果区域中包含拓朴关系则这个区域
只能有六个面。如果多于六个面则如图
4
所示可以使用
virtual
topology
对面进行合并直至所含的面只有六个面。
图
4
使用
virtual topology
对面进行合并直至所含的面只有六个
面
7
面与面之间的角度最好接近于
90
°
如果面与面角度
≥1500
则需进行
分割
8
对区域中的每个面则有以下要求
8.
1
如果区域不是立方体
cube
则其面
必须是一个整面单一面不
能含有多个面片
8 8.2
如果区域是立方体
cubea side can be a
connected set of faces that are on the
same geometric surface. In
addition the
pattern of the faces must allow rows and columns
of
hexahedral elements to be created in
a regular grid pattern along
that
entire side when the cube is meshed. For example
Figure 5
shows two acceptable face
patterns and the resulting regular grid
pattern of elements created by meshing
the cubes using the
structured meshing
technique. Figure 5 Acceptable face patterns
and the resulting meshes Figure 6
Unacceptable face patterns.
The face
pattern shown on the left is unacceptable for
structured
meshing because each face
has only three sides. Each face in the
pattern shown on the right has four
sides but the pattern does not
allow a
regular grid of elements to be created on the
partitioned
side of the cube as shown
in Figure 6. Figure 7 A regular grid of
elements cannot be created Abaqus
中三维几何体生成扫描网
格的分割方法
无法生成扫描网格的问题
分割示例
1
起始
面和目标面必须只能是一个整面
a
single face
或是四边形组
成的面片组合四边形的面
片可以生成规则网格
form a regular
grid
pattern
。图
1
所示
provides two examples of acceptable
connecting face patterns
图
1 provides two examples of
acceptable connecting face patterns
图
2 Unacceptable
connecting face patterns for swept
meshing 2
目标面必须只能
是一个整面当中没有独立
的边和顶点。如图
3
左边所示可以
使用
扫描网格因为独立的边和点都在起始面上而不在目标
面上而右边的则不能生成扫描网格因
为目标面上有两个面
片。图
4
显示了变截面网格沿着路径生成的扫描网格。
图
3 Only the region on the
left can be meshed using the swept
meshing technique
图
4 Sweeping the mesh along a
varying
cross-section
可以使用
virtual topology
< br>工具将目标面上的面
片合并起来从而使其可以使用扫描网格命令。图
5
便显示了
使用
virtu
al topology
工具合并了目标面的面片为一个整面因
为零件中含有
virtual
topology
所以它只能使用
advancing
front algorithm.
图
5 Combining faces makes a
part swept
meshable 3
对于旋转体截
面不能与旋转轴有任何相交的点
如图
6
所示。同样如图
7
所示截面的一条边与轴线相交但如
图
8
所示
mesh
the region with hexahedral-dominated elements
by generating layers of wedge elements
along the axis
。
图
6
The swept
meshing technique cannot mesh a part if an
isolated
point touches the axis of
revolution
图
7 Abaqus/CAE
cannot
mesh a region with hexahedral
elements if one or more edges lie
along
the axis of revolution
图
8
Abaqus/CAE can mesh the
region with
hexahedral-dominated elements
具体实例可见帮
助中的
17.17.7
Sweep meshing a solid revolved region whose
profile touches the axis of revolution
4
在旋转面的截面没有
与旋转轴相交如果再满足截面完整则可
以生成扫描网格。
图
9
的截面完整图
10
的截面丢失图
11
只有旋转轴上边没有
图
9
截面完整
图
10
截面丢失不能生成扫描网格
图
11
只
有旋转轴上边没有可以生成扫描网格
旋转区域使用样条曲
线生成的截面
sp
line
只有在
vertices at each end
of the spline
-
-
-
-
-
-
-
-
-
上一篇:在困难面前作文(15篇)
下一篇:GeoServer