ope-中转
Abaqus
常见的错误和解决方法
Fixed time is too large
Too many attamps have
been made
THE
SOLUTION APPEARS TO BE
DIVERGING
.
CONVERGENCE ISJUDGED
UNLIKELY
.
Time increment required is less than
the minimum specified
这样的信息几乎是无用信息(除了告诉
你的模型分析失败以外,没有告诉你任何有用的东
西)
。宜再查
找别的信息来考察。根据经验,改小增量步也不一定能收敛,虽然也有人报告
过改好的先
例,
我是从来没有遇到过,
也从来没有那个奢望。
所以我一般从模型的设置入手。
必须说明的是:
Error
和
warning
的性质是完全不同的。
p>
Error
意味着运算失败,
but
出现
warning
可能还能算,而且有些运
算必定会出现
warning
(比如接触分析必定出
“
负特征值
”
,
下有详述)
。很多警告只是通知性质的,或者只是说明一下而已,不一定
都是模型有问题。
比如以下
warning
完全可以忽略:
xxxxx will
(
not
)
printed
,这种只是通知你一声,某些玩意儿不输出了。
还有:
The parameter frequency cannot be used
with the parameter field. It will be ignored
(都说某某
被
ignored
了)
.
A
系列
如果模型能算,且结果合理,那么大部分警告信息可以不管。但是以下除外:
1
numerical sigularity(
数值奇异<
/p>
)
:刚体位移(欠约束)
solver
problem. numerical sigularity when processing
node105 instance
pile D.O.F. 1 ratio=1.735e13
2
Zero
pivot
(零主元)
:
过约束或者欠约束。
这
2
个问题一般都意味着模型约束存在问题。
1
)
、
2
< br>)都会伴随着产生大量负特征值。解决
方案当然第一步是检查约束了。
B
系列
有一些直接导致计算
aborted
,
那就得仔细分析了,比如:
1
xxxxx is not a valid in ABAQUS/Stand
ard(
告诉你这种计算
standard
不支持了,换别的
)
2
missing property
在
perperty
步检查材料属性是不是都加上了。
如果有梁单元,
看看
梁法向定义对了没有。
3
Detected lock file . Please confirm that no other
applications are attempting to write
to
the output database associated with
this job
before removing the lock file and resubmitting.
删除
.lck
文件就可以了,它是一个自动生成的文件。你也可
以另存为(另取名)
,再运
算。
4
The rigid part xx is
missing a refernce point
刚体(
or
刚体约束)都必须通过
stools--reference
point
给它定义一个参考点(
RP
)
,载
荷都加在这个
RP
上。
5
The area of 54 elements is zero,
small, or negative. Check coordinates or node
numbering, or
modify the mesh seed.
The elements 8 have been identified in
element set ErrElemAreaSmallNegZero
这个一般是节点编号不对的问题。必须是逆时针方向。
6
The
value
of
256
MB
that
has
been
specified
for
standard_memory
is
too small
to
run
the
analysis
and must be increased. The
minimum
possible value for standard_memory is 470 MB
7
HM to ABA
的问题:
集合和
面的几何的名称最好不要用特殊符号和数值
(特别是从
hm
p>
转过来)
,全部用英文字母是最安全的。
8
令很多人抓狂的
error code 5
1
)
使用
了子程序
,
子程序有问题
, (
p>
例如数组定义跟实际赋值不一致
,
这个我也
遇到过
)
2
)模型有问题
,
通常模型很大
,
很复杂
(
这个我没
遇到过
)
Please make
sure that the mesh density of the slave surface in
the tie
pair(
mbly__pic
kedset37_cns_,assembly__pickedsurf36)
is finer
than
the
master
surface.
The analysis may run slower, may yield
inaccurate results, and may require more
memory if this is not the case
3
)硬盘没空间了
(
这个其实不会引起
error code
5,
但是出错是肯定的了
),
或者是内
存太小
.
或
者产生的文件太大
.
4
)关闭杀毒软件试试(特别是卡巴)
5
)
有人认
为边界条件不正确
,
也会引起这个错误
.
9
system
error code 29539
关闭杀毒软件
and
try
。
10
**ERROR: Issue cannot
be deleted Not all data Released
在
windows
中,单击
“
控制面板<
/p>
”
--
“
系统<
/p>
”
--
“
高级<
/p>
”
--
“
性能设置
”
--
“
数据执行保护
”
命令,
p>
把
和<
/p>
添加进去。重起动后尝试
11
Surfaces
associated
with
analytical
rigid
part
MANDREL
may
have
their
orientation
flipped
刚体相连的接触面方向定义
反了,在接触定义的地方
edit
--
flip
12
CONTACT PAIR
(ASSEMBLY_BLANKBOT,ASSEMBLY_TIE-1_DIEDURF)
NODE BLANK-1.5 IS OVERCLOSED
BY
0.0512228 WHICH IS TOO
SEVERE
这往往是因为接触面的法线方向定义反了。定义刚体和<
/p>
shell
的
surface
时,要注意
选择外侧
13
123456
elements
are
dist
orted
。
Excessive
distortion
of
element
number
5
of
instance
PART-1-1
如果有子程序,一般不是材料设置有问题,就是边界条件的问题
14
XML
parsing
failure
for
job
1. Shutting
down
socket
and
terminating
all
further
messages. Please
check
the .log,
.dat, .sta, or .msg files for information about
the status of the job.
/viewthrea ... 26amp;typeid=68
15
The number of history
output requests in this ABAQUS analysis (>5000)
may cause SIGNIFICANT
performance problems during analysis and
postprocessing
输出项太多,恐硬件资源不够。要是你确保硬件够,这条也不怕了。一般的,应该
减少
History
中的输出项,尽量输出你最感兴趣的内容。
p>
16
V
alue for
parameter nset will be truncated to 80 characters
nset
名字取太长了,
p>
80
字符限制
17
compilation -
问题
Problem during compilation - not
found in PA
TH.
安装的时候没有装好或是
二次开发版本冲突。检查环境变量的设置;然后
verify
一下,看看是子程序功能否能通过?
C
系列
如上所说,有很多
warni
ng
并一定意味着你的模型存在问题。常被问起的有:
1
负特征值问题
THE SYSTEM
MA
TRIX HAS 8 NEGA
TIVE
EIGENV
ALUES.
负特征值是非线性分析的必然产物。
所以不必大惊小怪,
甚至久而久之,
对于你熟悉的
问题,你都会视而不见了。若出了问题,可先检查下有没有伴随的
numerical
sigularity(
数值奇异)和
Zero pivot
(零主元)产生。如果没有,
可以参考这几个方面:
1
)
.
刚体位移
2
)
.
单元
异常,过度变形、过度扭曲等
3
)
.
应力应变关系有负斜率
4
)如果有流体的话,在容器发生形变的话,也可能出现
negative
eigenvalue
的情况,不过不会出现警告,这是被允许的
5
)失稳发生
2
The ratio
of deformation speed to wave speed exceeds 1.0000
这个警告是指单元形变速度
V
(单元最大形变率
/
特征尺寸)和膨胀波速
C
(通过材料本构关系求得)的比例超过
1
。
解决这个问题的方案有以下几种
:
(
1
)检查单位是否封闭(参数设置有数量级的错误)
,此错误新手常犯;
(2)
检查网格质量
;
ope-中转
ope-中转
ope-中转
ope-中转
ope-中转
ope-中转
ope-中转
ope-中转
-
上一篇:外贸函电语气
下一篇:化妆品常用词汇中英文对照